Europe Middle East Africa Change

 

 

 Product

 

 

Remix each of the two components (part A and B) every time before using.
1. Mixing of the two components
Add 100 parts of BLUESIL RTV 3428 A to 10 parts of BLUESIL RTV 3428 B. The two components may be intimately mixed either by hand or using a low-speed electric or pneumatic mixer to minimize the introduction of air into the mixture.
The viscosity of BLUESIL RTV 3428 A&B can be reduced by using BLUESIL FLD 47V50, added up to 10% with respect to BLUESIL RTV 3428 A. This will improve flowing of the mixed product without causing significant changes of the mechanical properties of the elastomer.
Under no circumstances should this process can be applied for food moulding. In that case, the product must be used in its original formulation without any dilution, whatever it is.

2. Degassing
After mixing base and catalyst, it is recommended to eliminate entrapped air.
If the mixing is done with the help of a machine and a static mixer, both parts are degassed before mixing.
BLUESIL RTV 3428 A&B is degassed under a vacuum of 30 to 50 mbar. The degassing of the mixed product or of the two separated parts occurs under a vacuum of 30 to 50 mbar. Under vacuum, the product expands 3 to 4 times its initial volume and forms bubbles on its surface. These bubbles will disappear gradually and the mixture will sink back down to its initial volume within 5 minutes. Release the vacuum and repeat the operation a few minutes later.
Remark: release the vacuum several times improves the degassing. For easier degassing only fill a recipient to 1/3 of its height.
The product can be casted by gravity or under pressure.

3. Cross linking
The best curing conditions are at 23°C. When using the products at higher temperatures, the pot life is shorter and the setting rate faster. As opposed to this, lower temperatures increase the pot life and decrease the setting rate.
Room temperature curing assures the lowest possible shrinkage, if accelerated cure is desired, mild heat should be preferred. To minimize shrinkage the elastomer should be cured at maximum temperature of 60°C. Higher temperatures might cause higher shrinkage.
At 23°C, the cured silicone can be demoulded after the time indicated as "demolding time" (see § 2.Polymerization). In order to achieve the best possible performance levels from the pads, it is preferable to wait for 24 hours before using them.
Be aware that contact with certain materials can inhibit the curing of this RTV:

  • Natural rubbers vulcanized with sulphur
  • Polycondensation RTV catalysed with metal salts
  • PVC stabilizing agents
  • Amine cured epoxies
  • containing clays


In case of doubts, it is recommended to test the substrate by applying a small quantity of the mixed silicone on a restricted area. Take note that cross contaminations due to improperly cleaned tools or devices is the most frequent cause of inhibition.

 

 Use of BLUESIL RTV 3428 A + 3428 B ALL COLORS for the production of moulds for direct contact with food preparations

If cured according to the instructions described in the paragraph Characteristics of this datasheet, the chemical composition of BLUESIL RTV 3428 A&B ALL COLORS conforms with the positive lists of products approved by the regulations in force in the following countries: FRANCE: Journal Officiel, Brochure 1227; GERMANY: BGA, chapter XV-A; UNITED STATES: FDA Regulations, CFR-2 1.In all cases, the mould manufacturers must check that the moulds, in their future conditions of use, satisfy the EEC directive relative to migration tests: European Directive 93/8/EEC.

Purely for information purposes, migration tests have been carried out on prototype moulds in accordance with this directive. The results obtained showed that:

  1. In the special case of moulding of fat based products such as chocolate, the contact time between the mould and the melted foodstuff must be minimised: e.g. the duration of contact between the mould and the melted fatty product should not exceed 2 hours and the mould temperature should not exceed 40 °C.

  2. In the case of other foodstuff, the moulds may be used without any particular precautions in terms of duration of contact and temperature, whilst remaining within the temperature range compatible with the heat stability of silicone elastomers.

Note: In order to comply with the above mentioned directives, BLUESIL RTV 3428 A + 3428 B ALL COLORS must be mixed in the recommended ratio (A:B 10:1 w/w).

In food contact application context, under no circumstances should the product be diluted with silicone oil.

No special storage precautions noted. Material is stable under normal conditions. Avoid contact with oxidizing agents. Suitable containers: polyethylene. Plastic lined steel drum.Please consult the Safety Data Sheet of this product.Food Contact;Heavy Metals;RoHS;VOC

BLUESIL RTV 3428 B WHITE

The BLUESIL RTV 3428 A&B is a two component silicone elastomer which cures at room temperature by a polyaddition reaction. This reaction can be accelerated by heat. 

2 Part RTV

Fluid

Food Contact;Heavy Metals;RoHS;VOC

 

  • Easy processing and curing.
  • Outstanding tensile and tear strength.
  • Low linear shrinkage (when crosslinked at room temperature).
  • PART B: different colours available (see characteristics).
  • Once cured according to the conditions given in this technical data sheet, the chemical composition of BLUESIL RTV 3428 A&B conforms with the positive lists of products approved by the regulations in force in the following countries:

- FRANCE: Journal Officiel, Brochure 1227
- GERMANY: BGA, chapter XV-A
- UNITED STATES: FDA Regulations, CFR-2 1

For regulated applications, please contact Bluestar to ensure compliance and obtain the relevant statement.

 

 

  • Production of flexible moulds with excellent details reproduction, mechanical resistance and duration.
  • Production of thermal expansion formers for composite materials (the aeronautic industry, boat-building, etc.).
  • Production of moulds intended for moulding objects in chocolate, sugar, marzipan and for producing decorative sugar, pieces of bakery, biscuits and confectionery products.

 

Asia Pacific;Europe Middle East Africa;Central and South America

For information about Storage and Shelf Life for this product, please download the Technical Data Sheet.

 Characteristics_A

 

 

Viscosity8000PairedCompmPa.s
ColorWhitePairedComp

 Characteristics_B

 

 

Viscosity25000PairedCompmPa.s
ColorColourlessPairedComp

 

 

 Table_Characteristics_A_And_B

 

 

hardness_cd523e03-72a3-4261-93f9-36f7bbeeafb1hardness_cd523e03-72a3-4261-93f9-36f7bbeeafb1Hardness28PairedMixsh.A
pot-life_0d649a54-7503-4c7c-a047-9d0c4b3e9f6apot-life_0d649a54-7503-4c7c-a047-9d0c4b3e9f6aPot life60PairedMixmin
tear-strength_a14604f3-602f-4240-a9bf-15d90bbfbd13tear-strength_a14604f3-602f-4240-a9bf-15d90bbfbd13Tear strength20PairedMixKN/m

 

 

 

 

BLUESIL RTV 3428 ABLUESIL RTV 3428 A/our_offer/Product/90000452/90000746/BLUESIL-RTV-3428-A

 

 

 

 

 NeedAnExpert

 

 

 CS

 

 

 SS

 

 

 PressRelease

 

 

 

 

 Brochures

 

 

Why bother with plastic?https://www.bluestarsilicones.com/EN/Our_offer/KEC/ListInstance_Brochure_Title/JEC_Flyer.pdfWhy bother with plastic?

 TDS

 

 

 

 

 

 

BLUESIL RTV 3428 B PINKBLUESIL RTV 3428 B PINK/our_offer/Product/90000747/90000452/BLUESIL-RTV-3428-B-PINK
BLUESIL RTV 3428 B TRANSLUCENTBLUESIL RTV 3428 B TRANSLUCENT/our_offer/Product/90000748/90000452/BLUESIL-RTV-3428-B-TRANSLUCENT

 SQUARE_NEWS_EVENT_PRODUCT

 

 

JEC World 20172017-02-28T23:00:00ZThe Bluestar Silicones team promote our high performance RTV2 range for infusion molding at JEC World 2017 in Paris, France from March 14 to 16.The Bluestar Silicones team promote our high performance RTV2 range for infusion molding at JEC World 2017 in Paris, France from March 14 to 16.JEC World 2017https://www.bluestarsilicones.com/EN/Our_offer/Lists/Events_Marketing/Dispform.aspx?ID=57